HoonTruck: This raggy joint

By Jeff Glucker Apr 4, 2016

rag joint repair 4
Steering is generally considered an important piece of the automotive puzzle. When your steering goes bad, things can go wrong very quickly. I recently had the pleasure of experiencing what happens in an old truck when the steering coupler decides to give up. Thankfully, it was at its worst when I was only two miles from home and the major direction of travel was straight.
Still, it was like driving a slow, shitty boat trying to keep the truck tracking where I needed it to go. So, with a quick order placed into LMC Truck for a new part, it was time to get dirty under the HoonTruck hood.

rag joint repair 2
Now many of you will see this as a pretty easy job. And you’re right, it is certainly that as it only involves removing or merely loosening of a handful of bolts. Still, for yours truly it’s, on its face, daunting as it involves fiddling with the parts that keep me moving along my intended path.
This is what Sunday afternoons are for though, right? The sun was shining, the classic rock was playing cleanly through my Bluetooth speaker, and a delicious can of beer was resting on my engine.
rag joint repair 3]
The old rag joint came out with no fuss. Hell, parts of it came out simply by be me twisting and pulling on them with little effort. The rest of the part involved loosening where it attaches to the steering box and then loosening the steering column itself. I slid the old unit back and then out.
rag joint repair 5
The new unit was the installed in the reverse of the removal of the old part. It was easily accessible from both the top and the underside of the truck, which is where I found myself tightening part of the unit. You know, because I forgot for a moment that you could spin the whole damn thing. It was easier to get that “bottom” bolt started from underneath though, so I’m not a total moron here.
rag joint repair
I had other items I needed to take care of on this Sunday, so I didn’t get to fully tighten everything down. The column needs to be pushed into place so it and the steering wheel are flush. I’ll go back in there, tighten it all up and take it for a short test drive around the neighborhood. Then I’ll come back, check it all and make sure everything is still nice and tight.
As I said earlier, it’s probably a very easy fix for most of you. Now it’s also a very easy fix for me as well, yet it felt great to walk out of the garage knowing I actually fixed something in there.
[Images copyright 2016 Hooniverse/Jeff Glucker]

By Jeff Glucker

Jeff Glucker is the co-founder and Executive Editor of Hooniverse.com. He’s often seen getting passed as he hustles a 1991 Mitsubishi Montero up the 405 Freeway. IG: @HooniverseJeff

0 thoughts on “HoonTruck: This raggy joint”
  1. Wow, a rag joint with nylon in it? I’ve never seen that before. I’m used to the ones on GM cars, with fabric impregnated vulcanized rubber. Were the original Ford parts nylon, or are both of these an aftermarket type?

        1. And I’m sure this one will go bad in short order as well. They were steel fabric reineforced rubber from the factory for a reason. They need to flex and the rubber/steel will last a very long time unless they are soaked in oil in which case they will last a long time. Nylon will fatigue from the flexing. A short trip to the FLAPS will yield a Dorman replacement that while it won’t last the 30-50 years of the OE one it will last much longer than a Nylon one. Overall the Dorman unit would probably have been cheaper too. If not in the short term in the long term.

  2. Had a fabric/rubber one fail on a Mustang that was not really old enough to have such things fail. The joint had metal dogs that engaged after what felt like quarter turn of slop. I nursed it home like that, scary.

  3. Sounds like you need to have a good look at everything else that hasn’t been redone yet Jeff!

Leave a Reply

Your email address will not be published. Required fields are marked *

The maximum upload file size: 64 MB. You can upload: image, audio, video. Links to YouTube, Facebook, Twitter and other services inserted in the comment text will be automatically embedded. Drop files here